what do you need to make a cup turner
After searching and searching for a cup turner to be just the way I wanted it I finally gave up and took to the internet. I spent A LOT of time at Lowes and Home Depot trying to figure out and wrap my caput around exactly what I was trying to accomplish. Then hither we go! Hope it helps you and if yous have questions don't hesitate to reach out to me!
My married man and I started by making the "box" information technology consist of (ii) 40in pieces of 1in thick forest ( its not an actual 1in thick its more than similar iii/4 only its labeled 1in at the stores) 1 of those 40in pieces is vii one/4 tall and the other is 5 1/four tall. This is vary depending how high or depression you lot want your cups to sit down off of your table and where you put your holes. The sides are five ane/four alpine x v one/ii wide. These are nailed/glued together to brand a "box" BEFORE attaching everything we drilled holes nearly 1" in diameter through the taller back piece of the box (7 ane/4). I spaced mine roughly 8in from center of the hole to the next middle of the hole. We used a round hole cutter and a drill press, the aforementioned tin exist done with a paddle bit and a power drill. Next, we took the shorter front piece of the box and cut ane/2 circles off of the top of the wood so that they lined up with the holes cutting previously in the dorsum piece. You lot are creating an arm residual for your PVC and then it doesn't sag. You will also demand some sort of thin wood attached to either end to make legs, I learned the hard way that it will tip over. Pitiful we didn't take pictures of this, only it is pretty simple. If you lot are like me and need to encounter a pictures let me know and Ill get 1 for you but you should be able to see how it was done in after pictures on this post.
Now the fun role figuring out the arms and making everything connect to spin and what is needed from the store.. These are the items we bought from Lowe'due south All of the white PVC parts were constitute in the PVC connector section and the black plunger part was found in plumbing. WHEN You lot ARE LOOKING FOR THESE PARTS DONT TELL THEM WHAT Yous ARE TRYING TO DO, THEY GET VERY Confused AND ALL All of a sudden HAVE NO CLUE WHAT YOU ARE LOOKING FOR! or where to detect information technology! LOL 🙂
Picture 2 _ the bushing inserted into the plunger (you lot really have to put some umph into it to get information technology in there)
Picture iii – the adapter screwed into the bushing, this is where your PVC arm volition go and attach to the turner and your plunger will be in your cup
Now that you take your pieces and parts yous need to connect everything. We got a long 3/four dowel for Lowes or Home Depot as well. Each slice was cut to about 2.5 – 3 inches long and needed to exist sanded downward just a chip to make it a tad smaller to pit into the end of the adjustable repair coupling (shown in photo above) You volition also demand cotter pins for this step also. We drilled a hole into the finish of each dowel just big enough to fit the motor arm into, you only need to drill about 1/2 inch into the dowel. You can utilise a drill press, or Dremel merely it is Important that you get it as straight and centered every bit humanly possible. FYI this is a pain in the ass to get right! This concord your motor arm up to the down and put a marking on the side of the dowel where the hole in the motor arm is, so drill a hole just large plenty for the cotter pin to go through but not the head of the pin. Put your dowel on the motor arm, your cotter pin though and bend the arms of the cotter pin dorsum so you end up with this.…..
Now you desire to put that dowel through the pigsty you drilled in your taller piece of wood (once the box is assembled) eye it and screw your motor to the back of the forest and yous will have this..
Ok now that this is secure, yous will take your adjustable repair coupling and put the part that extends (yes its extendable! How genius is that!) onto the dowel, PUSH HARD making certain to support the motor so that you don't push button it out and drill a Woods screw through the PVC into the dowel arm so that information technology stays secure ( I conspicuously still need to do this and don't have a photo of it) Once that is complete you will have this….
Now we adhere our arm with the plunger attachment and get this..
Ok the switches.. this part sucks and my hubby definitely was the chief mind for this.. We got the cheap basic light switches and I knew I wanted each motor to run independently simply didn't want to have to take 5 separate plugs.. Hither is where things get messy… Nosotros attached the calorie-free switch to the top of the back piece on the peak so it could exist easily accessible ( if I wanted it prettier we would accept cut out squares large enough for me to put the back of the switch and the wire into the forest making the light switch flush and then covered with a light switch cover. I didn't care most all of that considering I am not selling these and then it didn't need to exist pretty just functional). We had a spool of wire that nosotros took each motor wire and spliced it into the 1 long wire and ran information technology to the terminate of the box calculation each motor wire to it as nosotros got to the next one until they were all attached to the one long wire. We so took a lamp switch and wired the i long wire (with all the motor wired spliced into it) and spliced information technology into the lamp switch wire. This allows us to plug in ONE plug and run each motor switch independently. Correct now we have it all stapled to the back (again not pretty) we are working on making a imitation lesser in the centre of the box to house all the wires under the false bottom. If you lot enclose information technology yous will have to take everything apart to replace anything as needed. For this just use shelf pegs and a thin piece of luan wood to sit on height of the pegs to hide the wires under it. Now you can only plough it over to access your wires if needed.
Here is our mess of wires right at present..
I actually hope this helps yall, I know I went through trial and lots of error before getting it like I wanted information technology. Sure I could buy one for $150+ simply why when I can brand it for way less and brand changes to information technology to suit my needs.
GOOD LUCK!
HUGE shout out to my amazing married man for ever helping me with my crazy projects and getting this just right for me!
Source: https://bellavoiphotography.com/diy-multiple-cup-turner/
0 Response to "what do you need to make a cup turner"
Post a Comment